VocationalLMSHelp center

Help center · Super Admin

V-69For the VocationalLMS Super Admin

Why it stopped: the reason in plain words, what failed, and how to continue

When a build stops, the course page explains it right under the red badge: the reason in plain words, which step and which lessons or chapter tests failed, what is left and what it costs, and the buttons Continue the build, Retry only the failed items, Skip and keep going and Copy details for support.

How-to video V-69 · 0:52

Read the words of this video

A build that stops no longer just says a step failed. Under the red badge, the Why it stopped panel gives the reason in plain words. Here the AI's answer for one chapter test was cut off because it was too long.

It names the step, shows how many finished, links the lessons or chapter tests that failed, and says what is left and what it will cost.

Then the buttons. Continue the build does everything unfinished. Retry only the failed items does just the failures, so the good work is not paid for twice. Skip hides the message, and Copy details for support copies everything for a message to us. A grey button says why: for example a mind map video job is running, and its Stop button is right there.

Open this in VocationalLMSAI Course Builder > a course > Why it stopped (under the red Build stopped badge)

Who can do this: The VocationalLMS Super Admin on master courses (a School Admin sees the same panel without provider names: A-121).

What it is for

A red Build stopped badge used to say only a step failed. The Why it stopped panel now sits right under the badge (and the badge's tooltip starts with one plain sentence) so nobody has to read the Activity log to learn what went wrong.

Steps

Read the reason

  1. Open the course. Under the title, Why it stopped gives the reason as a sentence: a provider out of credits or a refused key, the AI's answer was cut off (too long), an incomplete lesson, an update that interrupted the step, a busy service, a picture refused by the safety checker, a disk or memory problem, or a program error. Anything the system has not seen before is shown as The system recorded: ... with the first line of the real error, so nothing is hidden.
  2. Step says what was running and when (and the job in Activity). What failed lists the lessons or chapter tests that failed, each a link, with progress such as 17 of 18 finished. What is left says what remains and what it is expected to cost.

Continue

  1. Continue the build does everything still unfinished, in order (the same as Resume build, with the same provider check first).
  2. Retry only the failed items runs only the lessons and chapter tests that failed. The 17 tests that worked are not written or paid for again.
  3. Skip and keep going hides the message and changes nothing; the failed items can be written later with Resume build. When the course is complete and only an old error remains, the button reads Clear this message.
  4. Copy details for support copies the course, reason, step, job, failed items and the recorded error, ready to paste in a message.

When a button is grey

  1. Point at it: the tooltip says why, and the panel repeats it. A job is running (the panel shows it, with a Stop button): for example a mind map video job; the buttons come back when it finishes. Paused for a deploy: it resumes by itself. Nothing is left to build. When ElevenLabs has no characters left, the panel says voice steps will wait until the date they reset.
The Why it stopped panel under the Build stopped badge: the reason in plain words The failed chapter test, the step and what is left Continue the build, Retry only the failed items, Skip and keep going, Copy details for support

What happens next

When the work is done the panel goes away and the badge goes back to In progress or Ready. A chapter test that was cut off is now written again automatically in smaller pieces, so this stop should not come back for long chapters.

Common problems

#ProblemWhat to do
1The badge says Build stopped but nothing seems missing.The panel says so (The last step reported a problem, but nothing is missing now). Click Clear this message. Chapter tests waiting for review are not unfinished work.
2Retry only the failed items is grey but Continue the build is on.No failed lesson or chapter test is recorded; the stop was something else (an update, a provider). Use Continue the build.
3The reason says The system recorded: ...It is an error the system has no sentence for yet. Click Copy details for support and send it.

See also